[ak4250] ms0540-e-04 2010/06 - 1 - general description the ak4250 is a video amp with lp f. the output coupling capacit or can be removed because the ak4250 includes the negative power supply circuit. the ak4250 is housed in a space-saving 8-pin uson or 8-pin tmsop package. feature 1. video function ? a composite video input ? a video-amp (+6db) for composite video signal ? low pass filter ? charge pump circuit for negative power supply 2. ta = -40 85 c 3. power supply: 2.7 3.6v (typ. 3.0v) 4. power supply current: 10 ma 5. package: 8 pin uson (ak4250vu) 8 pin tmsop (AK4250VT) block diagram vin clamp lpf vout vdd charge pump clock generator pdn cp cn vss vee figure 1. ak4250 block diagram ak4250 output coupling capacitor-less video amp with lpf
[ak4250] ms0540-e-04 2010/06 - 2 - ordering guide ak4250vu ? 40 +85 c 8 pin uson (0.5mm pitch) AK4250VT ? 40 +85 c 8 pin tmsop akd4250 evaluation board for ak4250 pin layout ak4250vu 1 cp vdd top view 2 3 4 8 7 6 5 vin pdn vout vss vee cn AK4250VT top view cp vdd vin pdn cn vee vss vout 1 2 3 4 5 6 7 8
[ak4250] ms0540-e-04 2010/06 - 3 - pin/function no. pin name i/o function 1 cp o positive charge pump capacitor terminal pin 2 vdd - power supply pin. 3 vin i composite video signal input pin 4 pdn i power-down mode pin. internal pull down 100k . ? h ? : power up, ? l ? : power down. 5 vout o composite video signal driver pin 6 vss - ground pin 7 vee o negative voltage output pin for video amplifier 8 cn i negative charge pump capacitor terminal pin absolute maximum ratings (vss=0v; note 1 ) parameter symbol min max units power supplies: vdd ? 0.3 4.0 v input current, any pin except supplies iin - 10 ma input voltage ( note 2 ) vin ? 0.3 (vdd+0.3) or 4.0 v ambient temperature (powered applied) ta ? 40 85 c storage temperature tstg ? 65 150 c note 1. all voltages are with respect to ground. note 2. vin, pdin pins. max is sm aller value between (vdd+0.3)v and 4.0v vout pin becomes hi-z at the pdn pin = ?l?. therefore the vout pin is av ailable to signal line from another device by wired-or. the input si gnal to the vout pin must not ex ceed this input voltage range. any voltage must not be applied to the cn pin. warning: operation at or beyond these limits may result in permanent damage to the device. normal operation is not guaranteed at these extremes. recommended operating conditions (vss=0v; note 1 ) parameter symbol min typ max units power supplies vdd 2.7 3.0 3.6 v note 1. all voltages with respect to ground. * akm assumes no responsibility for the usage beyond the conditions in this datasheet.
[ak4250] ms0540-e-04 2010/06 - 4 - analog chracteristics (ta=25 c; vdd =3.0v; vss = 0v; unless otherwise specified) parameter conditions min typ max units v input characteristics input voltage - - 1.5 vpp input sync chip clamp voltage ( note 3 ) -0.386 -0.286 -0.186 v v output characteristics ( note 4 ) output gain vin=100khz, 0.2vpp 5.0 6.0 7.0 db maximum output voltage vin=100khz , thd=-30db 2.52 - - vpp s/n bw=100kh 6mhz, ( note 5 ) - 65 - db secondary distortion vin=3.58mhz, 0.2vpp (sin wave) - -45 - db load resistance 140 150 - load capacitance c1 ( figure 2 ) c2 ( figure 2 ) - - - - 15 400 pf pf lpf frequency response response at 6.75mhz -3 -0.5 - db input= 0.2vpp, sin wave response at 27mhz - -40 -20 db (0db at 100khz) group delay |gd3mhz - gd6mhz| - 10 100 nsec power supplies power up black signal is output and no load resistance. - 10 15 ma power down pdn pin = 0v - 1 2 a note 3. the charge pump circuit will not wo rk well, if the sync chip clamp voltage input to the vin pin is not within this voltage range. this sync chip clamp voltage is the voltage from the pedestal voltage note 4. the measurement point is the point a in figure 2 note 5. the reference signal is the 100% white signal. video signal output 75 ohm 75 ohm c2 r1 r2 c1 measurement point a figure 2. load capacitance c1 and c2 dc chracteristics (ta=25 c; vdd=2.7 3.6v) parameter symbol min typ max units high-level input voltage (pdn pin) low-level input voltage (pdn pin) vih vil 1.5 - - - - 0.6 v v
[ak4250] ms0540-e-04 2010/06 - 5 - video block the video amp has a drivability for a load resistance of 150 . the ak4250 has a composite input and output and includes a low pass filter (lpf). internal negative power s upply circuit supplies negative voltage to the video amp and video amp 0v output is used for a pedestal level. therefore, the output coupling capacitor can be removed. vdd charge pump cp cn vss vee 1uf 1uf negative power a k4250 (+) c2 c1 (+) note 6. c1 and c2 capacitors should have the low esr ( equivalent series resistance ) over all temperature range. when these capacitors have the polarity , the positive polarity pin should be c onnected to the cp pin and the vss pin. non polarity capacitors can also be used. figure 3. negative power supply circuit vout 75 a k4250 0v 75 figure 4. video signal output power down control when the pdn pin is ?l?, the ak4250 is forced to the power down mode (power consumption: typ 1 a). the vout pin becomes hi-z at the pdn pin = ?l?. the ak4250 includes a power-on-reset function. therefore any reset is not required externally.
[ak4250] ms0540-e-04 2010/06 - 6 - system design figure 5 shows the system connection diagram for the ak4250. an evaluation board [akd4250] is available which demonstrates the optimum layout, power supply arrangements and measurement results. top view power supply 2.7 3.6v dsp or p + 10 vdd 2 vin 3 pdn 4 cp 1 75 0.1u 8 7 6 5 cn vee vss vout 1 0.1 1 (+) (+) figure 5. typical connection diagram note: - any voltage must not be applied to the cn pin.
[ak4250] ms0540-e-04 2010/06 - 7 - package (ak4250vu) 8pin uson (unit: mm) 2.2 0.05 2.2 0.05 0.05 0.6max 1.2 0.05 1.9 0.05 0.25 0.05 0.5 0.2 0.05 0.05 m we recommend mounting this portion onto circuit b oard in order to secure mounting intensity. please do not connect to a power supply, gnd, signal line, etc. material & lead finish package molding compound: epoxy lead frame material: ni lead frame surface treatment: au plate
[ak4250] ms0540-e-04 2010/06 - 8 - package (AK4250VT) 8pin tmsop (unit: mm) m 0.1 4.00.2 2.8 2.9 +0.12 -0.1 0.65 0.127 +0.1 -0.05 0.550.2 0~10 0.95 max. 0.1 +0.1 -0.05 0.1 0.20.05 material & lead finish package molding compound: epoxy lead frame material: cu lead frame surface treatment: sn-bi (pb free)
[ak4250] ms0540-e-04 2010/06 - 9 - marking (ak4250vu) 250 x xx 1 xxx: date code (3 digit) marking (AK4250VT) 2 (1) #1pin indicator (2) chip no. (ak4xxx=xxx) (3) year 1 digit (4) month 1 digit (5) manage code (internal use) 8 (3) (4) (5) (1) 7 6 5 1 2 3 4 y 5 0 m a (2)
[ak4250] ms0540-e-04 2010/06 - 10 - revision history date (yy/mm/dd) revision reason page contents 07/03/28 00 first edition 07/11/05 01 spec change 4 power supply current consumption at power down max 20 a 2 a 08/09/05 02 error correct 8 marking was changed. 10/04/08 03 error correct 7 material & lead finish lead frame surface treatment: ag plate au plate 10/06/07 04 description addition the AK4250VT was added. important notice z these products and their specifications are subject to change without notice. when you consider any use or application of these produc ts, please make inquiries the sales office of asahi kasei microdevices corporation (akm) or authorized distributors as to current status of the products. z descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application exampl es of the semiconductor products. you are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your e quipments. akm assumes no responsibility fo r any losses incurred by you or third parties arising from the use of these information herein. akm assumes no liability for infringement of any patent, intellectual property, or other rights in the applica tion or use of such information contained herein. z any export of these products, or devices or systems containi ng them, may require an export license or other official approval under the law and regulations of the country of e xport pertaining to customs and tariffs, currency exchange, or strategic materials. z akm products are neither intended nor aut horized for use as critical components note1 ) in any safety, life support, or other hazard related device or system note2 ) , and akm assumes no responsibility fo r such use, except for the use approved with the express written consent by representative director of akm. as used here: note1 ) a critical component is one whose failure to functi on or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. note2 ) a hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aeros pace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z it is the responsibility of the buyer or distributor of akm products , who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above conten t and conditions, and the buyer or distributor agrees to assume any and all responsib ility and liability for and hold akm harmless from any and all claims arising from the use of said product in the absence of such notification.
|
